GroundWorx

Research & Learning

Root-Zone Profile Reading

One buried sensor can report several physically different quantities. This reference separates them — water content from saturation, tension from volume, bulk conductivity from saturation-extract conductivity — and shows what has to travel with each value for it to stay meaningful.

Root-Zone Profile Reading

What a buried profile actually reports: water content and tension as separate quantities, three different kinds of electrical conductivity, and why depth and timestamp travel with every value. General reference only — this page does not describe the GX-1 series' own measurement method or accuracy.

15 of 15 reference entries

Moisture

Water content and percent saturation are different numbers

Volumetric water content expresses the volume of water per volume of bulk soil, commonly in m³/m³ or percent by volume. Degree of saturation instead compares that water content with total porosity, so the same water content gives a different saturation in a porous soil than in a dense one.

What it does not tell you

A percentage on its own does not say which quantity it is. This page does not state which basis the GX-1 series reports on, and no percentage shown here should be read as the other quantity.

Keep with the record

The quantity name, its units, the porosity or texture it was compared against, and the depth it belongs to.

Moisture

Water tension says how hard a plant works, not how much water is there

Soil water tension is the suction a plant must overcome to extract water, so a rising tension means water is held more tightly rather than that a fixed volume has changed. The Wisconsin extension guide notes centibars are numerically equal to kilopascals and gives about 33 cb as a commonly used field-capacity suction for irrigation.

What it does not tell you

33 cb is a source-specific approximation for one context, not a universal field-capacity threshold, and it does not define permanent wilting point. Tension and matric potential also use opposite sign conventions.

Keep with the record

Whether the value is tension or matric potential, its sign convention and units, the depth, and the timestamp.

Moisture

Capacitance and TDR read an electrical property, then convert it

Both capacitance and time-domain reflectometry measure soil dielectric permittivity and convert it to water content through a calibration, rather than counting water volume directly. The METER manual states the raw value is converted to volumetric water content by a calibration equation specific to the substrate and encourages soil-specific calibration for added accuracy.

What it does not tell you

Shared principle, not identical instruments: the published frequency and accuracy figures in those manuals belong to those devices and are not attributed to the GX-1 series. A generic mineral-soil calibration is not interchangeable with a soil-specific one.

Keep with the record

The calibration equation or version used, the substrate or soil it applies to, and the measurement method.

Moisture

A dry reading can be an installation artifact

Sensor-to-soil contact matters: the METER manual instructs installers to minimize air gaps around the sensor and states that air gaps around the sensor needles result in low readings of soil moisture.

What it does not tell you

That error direction applies to that sensor design. It supports checking installation quality before believing a dry reading; it does not prove any particular reading is an artifact.

Keep with the record

Installation date and method, orientation, whether the backfill was disturbed or recompacted, and any suspected contact problem.

Salinity

Bulk EC, pore-water EC and saturation-extract EC are not one value

A buried probe can measure bulk-soil electrical conductivity directly, while ECe is measured on water extracted from a saturated soil paste. The METER manual distinguishes directly measured bulk EC, calculated pore-water EC, and saturation-extract EC, and temperature-corrects bulk EC to 25°C.

What it does not tell you

Units alone do not identify the basis. Neither bulk EC nor an estimated pore-water value should be labelled ECe without a justified conversion, and this page does not state which basis the GX-1 series reports.

Keep with the record

Which of the three quantities it is, the units, the temperature-compensation basis, and the conversion method if one was applied.

Salinity

Converting bulk EC to pore-water EC breaks down in dry soil

The conversion model described in the METER manual has a denominator that becomes very small below about 0.10 m³/m³ volumetric water content, producing large potential errors, and the manual does not recommend the calculation below that water content.

What it does not tell you

0.10 m³/m³ is a limit for that particular conversion method — not a universal sensor limit and not a plant-water-stress threshold. A calculated value is a model output, not a direct measurement.

Keep with the record

The conversion method, its stated valid moisture range, and the measured water content at the time of conversion.

Salinity

Salinity thresholds belong to a crop and a measurement basis

FAO's water-quality guidance tabulates crop tolerance against salinity, giving ECe values such as 1.0 dS/m for bean at full yield potential, 1.7 dS/m for corn, and 8.0 dS/m for barley, with separate values at 90% yield potential.

What it does not tell you

These are crop-response guidelines, not universal boundaries between safe and unsafe soil, and they are stated as ECe or irrigation-water EC — not as an unspecified buried-probe reading. Applying one to a different basis is unsupported.

Keep with the record

The crop and growth stage, whether the threshold is ECe or irrigation-water EC, and the measurement basis of the reading being compared.

Salinity

Leaching is what carries salts below the roots

FAO defines leaching fraction as the portion of applied water that passes through the entire rooting depth and percolates below, and contrasts a fraction of 0.5 with 0.1 to show that a higher fraction leaves less salt behind.

What it does not tell you

The fractions are illustrative, not irrigation prescriptions. Root-zone salt accumulation also depends on water quality, irrigation management and drainage, none of which a single reading establishes.

Keep with the record

Applied water volume, drainage below the root zone when measured, root-zone depth, and the water-quality analysis behind the salt load.

Salinity

Salinity changes with depth, so one reading is not an average

As a crop extracts water, salts concentrate in the soil water left behind, and as water percolates downward it moves salts through the profile, so salinity need not be uniform with depth. FAO's root-zone discussion treats salt concentration as varying through the rooting depth.

What it does not tell you

This is a general mechanism, not a guarantee of a neat pattern in any field: irrigation geometry, rainfall, preferential flow and groundwater all alter it. A reading at one depth is not automatically a root-zone average.

Keep with the record

The depth of each reading, the spacing between depths, and any drainage or irrigation event that could have moved salts between them.

Depth & temperature

Several depths resolve layers a single measurement cannot

Wisconsin extension describes multi-sensor systems as allowing simultaneous moisture measurement at several depths, and notes that to obtain a value for a specific depth the rods should be installed horizontally at that depth — so orientation determines which layer a reading represents.

What it does not tell you

This supports depth-specific sampling; it is not a quoted prohibition on single-sensor use, and it says nothing about the sensing volume of any particular device.

Keep with the record

Each sensor's depth, installation orientation, and the depth reference used (from the surface down, or from the sensor up).

Depth & temperature

Soil temperature is a depth and a time

A field study of a freezing soil measured the profile at 2, 5, 10, 20 and 50 cm and found the daily temperature signal gradually damped as it propagated deeper, becoming weak at 20 cm. A shallow reading therefore cannot stand in for a deeper one.

What it does not tell you

This is one field study, not a universal damping depth: snow cover, freezing, thermal properties and season all change the relationship. It supports keeping depth and timestamp together, not a fixed rule.

Keep with the record

The depth, the timestamp with time zone, and the sampling or averaging interval behind each temperature value.

Depth & temperature

Surviving a freeze is not the same as measuring in one

Freezing lowers dielectric permittivity, and the METER manual for a ceramic-matrix water-potential sensor states plainly that it does not accurately measure water potential in frozen soil conditions.

What it does not tell you

That statement covers that instrument and quantity. It is used here as a principle — frozen-ground readings need their own validity check — and is not a claim about any specific GroundWorx sensor's freeze behaviour.

Keep with the record

Whether the ground was frozen, the frozen-state validity statement for the instrument actually used, and quality flags for those periods.

Depth & temperature

A wet layer at depth may not be the water table

The USDA Agricultural Thesaurus defines a perched water table as the upper surface of a local zone of soil-water saturation held above the main body of groundwater by an impermeable layer, and separated from that main body by an unsaturated zone.

What it does not tell you

This names a mechanism; it is not a diagnostic method. Telling perched water from regional groundwater, recent irrigation wetting or slow drainage needs profile and site evidence beyond a deep wet reading.

Keep with the record

The depth of the wet layer, the texture or horizon above and below it, and the irrigation or rainfall history preceding it.

Keeping the record

The same water content means different things in different soils

Wisconsin extension identifies texture and organic matter as major drivers of water-holding capacity, gives illustrative field capacities of about 9% by volume for sand, 21% for sandy loam, 27% for loam and 40% for clay, and recommends separately monitoring and managing heavy- and light-soil areas.

What it does not tell you

Those are generalized texture-class values, not site calibration targets, and they do not quantify within-field salinity variability or any sensor's sensing volume.

Keep with the record

Soil texture or horizon at each location, the areas treated as separately managed, and which reading belongs to which zone.

Keeping the record

Keep the interpretation with the number

Taken together, the cited manuals and guides treat a reusable soil record as more than a value: quantity and units, depth and location, timestamp, calibration or conversion method, soil type and installation condition are what let two readings be compared at all.

What it does not tell you

This is an editorial synthesis of several sources, not compliance with a named formal data standard, and it does not prescribe a schema. It cannot by itself prove a reading is accurate.

Keep with the record

Timestamp with time zone, location and depth with its reference, quantity and units, calibration or conversion version, soil texture, installation notes, and quality flags for frozen, disturbed, missing or out-of-range periods.

Sources reviewed November 20, 2026 and reachable on that date; pages that blocked automated retrieval were left out rather than substituted. This is general reference for turf, trees and crops. It does not establish the GX-1 series' sensing technology, calibration, sensing volume, freeze behaviour or accuracy — confirm those against GroundWorx technical documentation. Original publisher guidance remains the source of record.

Reference, not a specification

These pages describe how published soil-water and salinity guidance treats the quantities a buried profile reports. They do not establish the measurement method, calibration, sensing volume, freeze behaviour or accuracy of any GroundWorx hardware, and they are not irrigation or reclamation advice for a specific site. Compare thresholds only against readings expressed on the same basis, and ask a qualified adviser before acting on a site.

Reference reviewed November 20, 2026. Original publisher guidance remains the source of record.